Debian stretch y las tarjetas externas

Koala · 18-10-2018 15:55:21

Hola a todos cool

Entre 2 viajes, vengo de installar debian 9 sobre un ordenador con mi 2 tarjetas alfa (la 36h y la ach) y con los dos no quiere conectarse.Normalmente la 36H esta reconocido desde tiempo pero aqui tambien no se conecta.Despuès he installado el driver de la ach como habia hecho varias veces con otros ordenador y tan poco me anda.

He hecho los básicos, ip link tarjeta up, rfkill etc...

A ver si tenéis idea de dónde puede venir eso, dejo aquí salidas de consola.

uname -a
Linux koala 4.9.0-8-amd64 #1 SMP Debian 4.9.110-3+deb9u6 (2018-10-08) x86_64 GNU/Linux

[email protected]:/home/flow# ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: eno1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 1000
    link/ether a4:5d:36:7e:a8:25 brd ff:ff:ff:ff:ff:ff
3: wlo1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DORMANT group default qlen 1000
    link/ether 0c:84:dc:70:80:c7 brd ff:ff:ff:ff:ff:ff
4: wlx00c0ca96482c: <NO-CARRIER,BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state DORMANT mode DORMANT group default qlen 1000
    link/ether ae:8b:78:41:6c:db brd ff:ff:ff:ff:ff:ff

modo dormant ? hmm tambien la mac esta especial pero eso lo puedo cambiar con udev y no me arregla el problema

[email protected]:/home/flow# dmesg | grep -e wlan -e 8821au
[   12.334674] rt2800pci 0000:07:00.0 wlo1: renamed from wlan0
[11642.449345] 8812au 1-1.2:1.0 wlx00c0ca96482c: renamed from wlan0

IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[   24.349717] r8169 0000:08:00.0: firmware: direct-loading firmware rtl_nic/rtl8106e-1.fw
[   24.551805] r8169 0000:08:00.0 eno1: link down
[   24.551862] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[   24.661814] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[   24.661893] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt3290.bin'
[   24.705301] rt2800pci 0000:07:00.0: firmware: direct-loading firmware rt3290.bin
[   24.705326] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.37
[   24.776087] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[   24.848043] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[   27.693737] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[   34.368269] fuse init (API version 7.26)
[  370.164554] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[  685.188302] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 1000.196051] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 1315.199804] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 1630.207551] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 1945.219299] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 2260.227052] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 2575.230797] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 2890.242557] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 3205.246301] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 3520.258055] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 3835.261803] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 4150.269546] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 4465.277297] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 4780.289047] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 5095.292794] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 5410.292549] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 5725.252293] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 6040.276049] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 6355.295798] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 6670.319547] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 6985.343297] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 7300.347048] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 7615.354798] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 7930.354540] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 8245.370294] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 8560.322046] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 8875.389796] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 9190.373551] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 9505.405301] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[ 9820.413049] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[10135.412792] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[10450.424546] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[10765.432299] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[11080.440044] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[11395.447797] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[11396.771828] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[11396.946359] wlo1: authenticate with 02:0c:e7:89:0b:26
[11396.955641] wlo1: send auth to 02:0c:e7:89:0b:26 (try 1/3)
[11396.957778] wlo1: authenticated
[11396.959507] wlo1: associate with 02:0c:e7:89:0b:26 (try 1/3)
[11396.963971] wlo1: RX AssocResp from 02:0c:e7:89:0b:26 (capab=0x431 status=0 aid=1)
[11396.964078] wlo1: associated
[11397.039294] IPv6: ADDRCONF(NETDEV_CHANGE): wlo1: link becomes ready
[11627.409605] usb 3-1: new low-speed USB device number 4 using xhci_hcd
[11627.553210] usb 3-1: New USB device found, idVendor=0000, idProduct=0538
[11627.553215] usb 3-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[11627.553218] usb 3-1: Product:  USB OPTICAL MOUSE
[11627.556352] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:14.0/usb3/3-1/3-1:1.0/0003:0000:0538.0003/input/input18
[11627.556742] hid-generic 0003:0000:0538.0003: input,hidraw2: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:00:14.0-1/input0
[11640.677787] usb 1-1.2: new high-speed USB device number 3 using ehci-pci
[11640.786698] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=8812
[11640.786702] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[11640.786705] usb 1-1.2: Product: 802.11n NIC
[11640.786707] usb 1-1.2: Manufacturer: Realtek
[11640.786709] usb 1-1.2: SerialNumber: 123456
[11640.898715] 8812au: loading out-of-tree module taints kernel.
[11641.770426] usb 1-1.2: reset high-speed USB device number 3 using ehci-pci
[11641.879225] usb 1-1.2: device firmware changed
[11641.879571] usbcore: registered new interface driver 8812au
[11641.879751] usb 1-1.2: USB disconnect, device number 3
[11641.966556] usb 1-1.2: new high-speed USB device number 4 using ehci-pci
[11642.075677] usb 1-1.2: New USB device found, idVendor=0bda, idProduct=8812
[11642.075682] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[11642.075684] usb 1-1.2: Product: 802.11n NIC
[11642.075687] usb 1-1.2: Manufacturer: Realtek
[11642.075689] usb 1-1.2: SerialNumber: 123456
[11642.449345] 8812au 1-1.2:1.0 wlx00c0ca96482c: renamed from wlan0
[11642.482590] IPv6: ADDRCONF(NETDEV_UP): wlx00c0ca96482c: link is not ready
[11643.039261] IPv6: ADDRCONF(NETDEV_UP): wlx00c0ca96482c: link is not ready
[11643.039282] IPv6: ADDRCONF(NETDEV_CHANGE): wlx00c0ca96482c: link becomes ready
[11643.097333] IPv6: ADDRCONF(NETDEV_UP): wlx00c0ca96482c: link is not ready
[11766.429351] wlo1: deauthenticating from 02:0c:e7:89:0b:26 by local choice (Reason: 3=DEAUTH_LEAVING)
[11766.532306] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[11769.974360] IPv6: ADDRCONF(NETDEV_UP): wlx00c0ca96482c: link is not ready
[11795.308783] IPv6: ADDRCONF(NETDEV_UP): wlx00c0ca96482c: link is not ready
[11795.336625] IPv6: ADDRCONF(NETDEV_UP): wlx00c0ca96482c: link is not ready
[11840.850229] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[11842.054237] wlo1: authenticate with 02:0c:e7:89:0b:26
[11842.077625] wlo1: send auth to 02:0c:e7:89:0b:26 (try 1/3)
[11842.080184] wlo1: authenticated
[11842.081562] wlo1: associate with 02:0c:e7:89:0b:26 (try 1/3)
[11842.085243] wlo1: RX AssocResp from 02:0c:e7:89:0b:26 (capab=0x431 status=0 aid=1)
[11842.085347] wlo1: associated
[11842.103711] IPv6: ADDRCONF(NETDEV_CHANGE): wlo1: link becomes ready
[11957.080893] wlo1: deauthenticating from 02:0c:e7:89:0b:26 by local choice (Reason: 3=DEAUTH_LEAVING)
[11957.190590] IPv6: ADDRCONF(NETDEV_UP): wlo1: link is not ready
[11961.237025] IPv6: ADDRCONF(NETDEV_UP): wlx00c0ca96482c: link is not ready

Gracis a todos para las futuras repuestas smile

kcdtv · 18-10-2018 17:07:31

Link State
In the context of link state, DORMANT indicates the interface is not in a condition to pass packets but is instead in a "pending" state waiting for some external event. For an interface to be usable for forwarding, it should be in an UP state as it is in the output shown above.
Resolution
It is expected to see mode DORMANT in the output of ip link show for MLAG bond downlinks. For traffic to be forwarded on those interfaces, ensure that the bond link state is state UP.

(visto aquí)
El modo DORMANT bien podría ser causa del problema.
¿Has probado cambiarlo a default?

sudo ip link set wlo1 mode default

Koala · 18-10-2018 17:38:58

Vengo de intentar y no cambia nada, voy a ver lo que encuentro sobre el modo "dormant"

kcdtv · 18-10-2018 19:30:47

¿Has probado en la interfaz wlo1?
Porque en la wlxmacUSB hay también el "estado" que está en modo dormilón.
Quizá en lugar de default inténtalo con up
Debo salir un rato, luego me pasaré por aquí ya que me has intrigado que tu historia de modo "dormant" big_smile

Koala · 18-10-2018 21:00:55

He probado up y default y se queda igual en "dormant" tongue , lo que no comprendo es que la tarjeta interna anda bien, séguiré probando cosas manana.

Koala · 27-10-2018 15:35:17

Para que lo sabeis

el problemo no venia de debian pero de network manager que no accepta las tarjetas wifi con el nombre wlx, el nombre tiene que empezar por wlp o wlo

Hay que cambiar de nombre la interfaz antes de usar lo, despuès todo anda bien.No pongo las fuentes porqué esta en frances nadie va a comprender nada tongue

Tema	Respuestas	Vistas	Ultimo mensaje
Usar puerto usb para almacenamiento Arcadyan VR9517VAC22-A-OS-AM por maxi	0	165	Ayer 00:30:11 por maxi
Llega el caós con las nuevas interfaces wifi wlxXXXXXXXXXXX por kcdtv	14	2412	29-06-2022 13:19:48 por kcdtv
Error de inicio en entorno gráfico por Hunter310#	24	15134	20-06-2022 12:22:19 por kcdtv
Cómo usar Proton VPN (gratis y realmente seguro) en linux por kcdtv	15	2746	10-06-2022 09:13:42 por kcdtv
LibRedirect acceso sin rastreo a youtube, instagram, tik tok, twitter por kcdtv	0	252	02-06-2022 10:05:09 por kcdtv

Foro Wifi-libre.com

Anuncio

#1 18-10-2018 15:55:21